rathole

English | 简体中文

A secure, stable and high-performance reverse proxy for NAT traversal, written in Rust

rathole, like frp and ngrok, can help to expose the service on the device behind the NAT to the Internet, via a server with a public IP.

• rathole
  • Features
  • Quickstart
  • Configuration
    • Logging
    • Tuning
  • Benchmark
  • Planning

Features

• High Performance Much higher throughput can be achieved than frp, and more stable when handling a large volume of connections. See Benchmark
• Low Resource Consumption Consumes much fewer memory than similar tools. See Benchmark. The binary can be as small as ~500KiB to fit the constraints of devices, like embedded devices as routers.
• Security Tokens of services are mandatory and service-wise. The server and clients are responsible for their own configs. With the optional Noise Protocol, encryption can be configured at ease. No need to create a self-signed certificate! TLS is also supported.
• Hot Reload Services can be added or removed dynamically by hot-reloading the configuration file. HTTP API is WIP.

Quickstart

A full-powered rathole can be obtained from the release page. Or build from source for other platforms and minimizing the binary. A Docker image is also available.

The usage of rathole is very similar to frp. If you have experience with the latter, then the configuration is very easy for you. The only difference is that configuration of a service is split into the client side and the server side, and a token is mandatory.

To use rathole, you need a server with a public IP, and a device behind the NAT, where some services that need to be exposed to the Internet.

Assuming you have a NAS at home behind the NAT, and want to expose its ssh service to the Internet:

1. On the server which has a public IP

Create server.toml with the following content and accommodate it to your needs.

# server.toml
[server]
bind_addr = "0.0.0.0:2333" # `2333` specifies the port that rathole listens for clients

[server.services.my_nas_ssh]
token = "use_a_secret_that_only_you_know" # Token that is used to authenticate the client for the service. Change to an arbitrary value.
bind_addr = "0.0.0.0:5202" # `5202` specifies the port that exposes `my_nas_ssh` to the Internet

Then run:

./rathole server.toml

2. On the host which is behind the NAT (your NAS)

Create client.toml with the following content and accommodate it to your needs.

# client.toml
[client]
remote_addr = "myserver.com:2333" # The address of the server. The port must be the same with the port in `server.bind_addr`

[client.services.my_nas_ssh]
token = "use_a_secret_that_only_you_know" # Must be the same with the server to pass the validation
local_addr = "127.0.0.1:22" # The address of the service that needs to be forwarded

Then run:

./rathole client.toml

3. Now the client will try to connect to the server myserver.com on port 2333, and any traffic to myserver.com:5202 will be forwarded to the client's port 22.

So you can ssh myserver.com:5202 to ssh to your NAS.

To run rathole run as a background service on Linux, checkout the systemd examples.

Configuration

rathole can automatically determine to run in the server mode or the client mode, according to the content of the configuration file, if only one of [server] and [client] block is present, like the example in Quickstart.

But the [client] and [server] block can also be put in one file. Then on the server side, run rathole --server config.toml and on the client side, run rathole --client config.toml to explicitly tell rathole the running mode.

Before heading to the full configuration specification, it's recommend to skim the configuration examples to get a feeling of the configuration format.

See Transport for more details about encryption and the transport block.

Here is the full configuration specification:

[client]
remote_addr = "example.com:2333" # Necessary. The address of the server
default_token = "default_token_if_not_specify" # Optional. The default token of services, if they don't define their own ones
heartbeat_timeout = 40 # Optional. Set to 0 to disable the application-layer heartbeat test. The value must be greater than `server.heartbeat_interval`. Default: 40 seconds
retry_interval = 1 # Optional. The interval between retry to connect to the server. Default: 1 second

[client.transport] # The whole block is optional. Specify which transport to use
type = "tcp" # Optional. Possible values: ["tcp", "tls", "noise"]. Default: "tcp"

[client.transport.tcp] # Optional. Also affects `noise` and `tls`
proxy = "socks5://user:[email protected]:1080" # Optional. The proxy used to connect to the server. `http` and `socks5` is supported.
nodelay = true # Optional. Determine whether to enable TCP_NODELAY, if applicable, to improve the latency but decrease the bandwidth. Default: true
keepalive_secs = 20 # Optional. Specify `tcp_keepalive_time` in `tcp(7)`, if applicable. Default: 20 seconds
keepalive_interval = 8 # Optional. Specify `tcp_keepalive_intvl` in `tcp(7)`, if applicable. Default: 8 seconds

[client.transport.tls] # Necessary if `type` is "tls"
trusted_root = "ca.pem" # Necessary. The certificate of CA that signed the server's certificate
hostname = "example.com" # Optional. The hostname that the client uses to validate the certificate. If not set, fallback to `client.remote_addr`

[client.transport.noise] # Noise protocol. See `docs/transport.md` for further explanation
pattern = "Noise_NK_25519_ChaChaPoly_BLAKE2s" # Optional. Default value as shown
local_private_key = "key_encoded_in_base64" # Optional
remote_public_key = "key_encoded_in_base64" # Optional

[client.transport.websocket] # Necessary if `type` is "websocket"
tls = true # If `true` then it will use settings in `client.transport.tls`